general Section
- continuous-no-signal
- conversation-file-name-prefix
- cpd-file-name-prefix
- cpd-if-established
- cpd-recording
- destination-busy-timeout
- keep-channels-open
- line-type
- location
- max-number-ports-to-record
- off-hook-delay
- off-hook-timeout
- on-hook-timeout
- out-of-service-attempts
- out-of-service-timeout
- post-connect-cpd-priority
- pre-connect-cpd-priority
- sit-detection
- tscall
- tsclear
- use-busy2-as-nu-tone
- use-engaging-lines
- use-fax2-as-am-tone
- wait-off-hook
continuous-no-signal
Default Value: 20
Valid Values: Any integer in the range from 0 to MAXINT
Changes Take Effect: Takes effect immediately
Specifies the time, in seconds, of continuous silence (no ring back timeout).
conversation-file-name-prefix
Default Value: conv_
Valid Values: Any ASCII string.
Changes Take Effect: Takes effect after restart
Specifies the prefix for the file name for the conversation recording file.
cpd-file-name-prefix
Default Value: cpd_
Valid Values: Any ASCII string
Changes Take Effect: Takes effect after restart
Specifies the prefix for the file name for the call result recording file.
cpd-if-established
Default Value: false
Valid Values: Yes/True or No/False
Changes Take Effect: Takes effect immediately
Controls the way the pre-connect Call Progress Analysis (CPA) is performed. If set to true or yes, Dialogic CPA is engaged after the EventEstablished message has been received.If set to false or no, Dialogic CPA is engaged immediately at the beginning of the call start.
cpd-recording
Default Value: false
Valid Values: Yes/True or No/False
Changes Take Effect: Takes effect immediately
Enables recording of call progress detection.
destination-busy-timeout
Default Value: 2000
Valid Values: Any integer in the range from 0 to MAXINT
Changes Take Effect: Takes effect immediately
CPD Server normally waits for both of the following indicators that a dialed number is busy before it terminates call progress detection: 1) busy call result from the Dialogic board; 2) EventDestinationBusy from T-Server. This option prevents CPD Server from waiting indefinitely for a Busy call result by specifying the length of time (in milliseconds) that CPD Server waits for confirmation of the call result from the second source after the first has arrived. When the timeout expires, CPD Server accepts the Busy call result as correct.
keep-channels-open
Default Value: false
Valid Values: Yes/True or No/False
Changes Take Effect: Takes effect immediately
Determines how CPD Server uses Dialogic channels. When set to yes, CPD Server keeps all Dialogic channels open and reuses them for the next call. CPD Server is unable to process dynamic option changes when this value is specified. When set to no, CPD Server closes the Dialogic channels after use and reopens them for the next call.
line-type
Default Value:
Valid Values: Please select value from the list
Changes Take Effect: Takes effect after restart
Specifies the type of line (Dialogic card) that is being used. It also specifies the type of the protocol used to connect the Dialogic board to the switch or PSTN.
location
Default Value:
Valid Values: Any string.
Changes Take Effect: Takes effect after restart
Specifies the name of the folder under the DN section of the Switch object of the T-Server application that CPD Server uses when dialing.
max-number-ports-to-record
Default Value: 0
Valid Values: Any integer in the range from 0 to MAXINT
Changes Take Effect: Takes effect immediately
Specifies the maximum number of agent ports on which to record at the same time. The value of the max-number-ports-to-record is limited by two factors: 1) the number of configured recording ports; 2)the hardware limit for the number of Dialogic ports per box
off-hook-delay
Default Value: -1
Valid Values: Any integer in the range from -MAXINT to MAXINT
Changes Take Effect: Takes effect immediately
Specifies the delay, in seconds, between off-hook and TMakeCall: if set to a negative value - off-hook, and then tmakecall; if set to a positive value - tmakecall, and then off-hook.
off-hook-timeout
Default Value: 1
Valid Values: Any positive integer.
Changes Take Effect: Takes effect immediately
Specifies the amount of time to wait, in seconds, that CPD Server waits before assuming that the channel is in the off-hook state.
on-hook-timeout
Default Value: 1
Valid Values: Any non-negative integer
Changes Take Effect: Takes effect immediately
Specifies the amount of time, in seconds, that CPD Server waits before assuming that the channel is in an on-hook state.
out-of-service-attempts
Default Value: 2
Valid Values: Any non-negative integer; minimum 2
Changes Take Effect: Takes effect immediately
Specifies the number of failed attempts to use a port (channel) before CPD Server marks it out of service.
out-of-service-timeout
Default Value: 1
Valid Values: Any non-negative integer.
Changes Take Effect: Takes effect immediately
Specifies the amount of time (in minutes) that CPD Server waits before trying to use an out-of-service port again. If the value is 0, CPD Server ignores out-of-service conditions and continues to attempt to use the port.
post-connect-cpd-priority
Default Value: tserver
Valid Values: Please select value from the list
Changes Take Effect: Takes effect immediately
Defines the CPD priority for post-connect CPA. This option works together with the pre-connect-cpd-priority option.
pre-connect-cpd-priority
Default Value: tserver
Valid Values: Please select value from the list
Changes Take Effect: Takes effect immediately
Defines the source of Call Progress Information that is used for pre-connect CPA.
sit-detection
Default Value: true
Valid Values: Yes/True or No/False
Changes Take Effect: Takes effect immediately
Defines the SIT signal parameters in the Dialogic DX_CAP data structure to enable CPD Server to more easily identify a SIT signal.
tscall
Default Value: false
Valid Values: Yes/True or No/False
Changes Take Effect: Takes effect immediately
Specifies whether CPD Server sends a request to T-Server (tscall = true or yes) or to Dialogic board (tscall = false or no) to make a call.
tsclear
Default Value: false
Valid Values: Yes/True or No/False
Changes Take Effect: Takes effect immediately
Controls the way a call is released. If this option is set to yes, a RequestClearCall (G3 specific) is issued to release an active call. This option is useful, but not required, if a two-step transfer fails on a G3 switch.
use-busy2-as-nu-tone
Default Value: false
Valid Values: Yes/True or No/False
Changes Take Effect: Takes effect immediately
Controls the way in which the Busy2 tone is detected. This option enables CPD Server to detect a NU (Number Unobtainable) tone call result by using the Busy2 tone. When the value is set to yes, the NU tone call result is assigned to all Busy2 tone detected calls. You can set this option at the Application level.
use-engaging-lines
Default Value: false
Valid Values: Yes/True or No/False
Changes Take Effect: Takes effect after restart
Applicable only to ASM mode.If set to no or false, CPD Server engages agents by using lines from the regular lines pool - that is, from the regular folder. If set to yes or true, CPD Server engages agents by using lines from a special lines pool that is dedicated to engaging purposes - that is, from the engaging folder.
use-fax2-as-am-tone
Default Value: false
Valid Values: Yes/True or No/False
Changes Take Effect: Takes effect immediately
Controls the way in which the Fax2 tone is detected. This option enables CPD Server to detect an Answering Machine call result by using the Fax2 tone. When the value is set to yes, the Answering Machine call result is assigned to all Fax2 tone detected calls.
wait-off-hook
Default Value: false
Valid Values: Yes/True or No/False
Changes Take Effect: Takes effect after restart
Specifies whether CPD Server waits (a value of yes or true) or does not wait (a value of no or false) for an off-hook event from T-Server. Note: This value is used when the tscall option has a value of true and the off-hook-delay option has a negative value.